Account

What new tool do you want?

Health & Fitness

Fiber Intake Calculator

Find your recommended daily fiber intake from your age, sex or calorie intake, based on the US Dietary Guidelines (14 g per 1,000 kcal).

For general information only — not medical advice. Results are estimates; talk to a doctor or qualified health professional about your own health.

How to use

  1. 1Enter your age and sex, or your daily calories.
  2. 2Compare the target with how much you currently eat.

How it's calculated

Adequate intake = 14 g of fiber per 1,000 kcal (Institute of Medicine / US Dietary Guidelines). Age-based targets: men 38 g (19–50) and 30 g (51+); women 25 g and 21 g.

Frequently asked questions

What foods are high in fiber?

Beans and lentils, whole grains, oats, vegetables, fruit with skin, nuts and seeds.

Can I eat too much fiber?

Increasing quickly can cause bloating. Raise it gradually and drink more water.

Is the UK recommendation different?

The UK recommends 30 g a day for adults, measured with a slightly different method (AOAC).

Two different targets that can disagree with each other

This calculator has two ways to arrive at a fiber target: a flat age-and-sex figure (38 g for men 19–50, dropping to 30 g at 51+; 25 g and 21 g for women) or a calorie-based one (14 g per 1,000 kcal) whenever a calorie figure is entered. These aren't two views of the same number — they can genuinely disagree. A 30-year-old man eating 2,000 kcal a day would get a 38 g target from the age-based figure but only 28 g from the calorie-based one, because the age-based number assumes a 'typical' calorie intake for that demographic that doesn't necessarily match any individual.

Why the age-based targets really track calories, not age itself

The reason men's targets are higher than women's, and younger adults' targets are higher than older adults', isn't that fiber needs change biologically with age or sex — it's that the 14 g-per-1,000-kcal rule was applied to typical calorie intakes for each group, and those typical intakes differ by age and sex. In other words, the age-and-sex table is really the calorie-based rule already baked in using population averages, which is exactly why entering your actual calorie intake overrides it with a more individually accurate number.

Why the gap number matters more than the raw target

Most adults in the US and similar countries eat well under half the recommended fiber, so the 'still to add' output — the difference between your target and your current intake — is often a more useful starting point than the target alone. Fiber intake is also one of the few dietary changes where increasing too quickly causes its own problems (bloating, gas), so a visible gap is useful mainly as a sense of how much room there is to add foods gradually, not a number to close in a single day.

Worked example: Fiber Intake Calculator

A 30-year-old woman eating 2,000 kcal a day with a current fiber intake of 15 g gets a calorie-based target of (2,000 ÷ 1,000) × 14 = 28 g — 13 g more than she currently eats. Without entering her calorie intake, the age-based target for a woman under 51 would instead show 25 g, a few grams lower, since that flat figure assumes a somewhat different typical calorie intake than her actual 2,000 kcal.

Leave current intake blank and the gap disappears

Sex starts on female and age on 35, with calories and current intake empty, so the page opens on the age-based target of 25 g and there is no still-to-add line. That line appears only after you type a current intake. If you are already at or above the target, the label changes from Still to add to Above target by. Calories are used only when the number is greater than zero. Zero, or a blank calorie box, keeps the age table. The age switch is at 51: age 50 still uses 38 g for men and 25 g for women, and age 51 uses 30 g and 21 g. The target is a whole number of grams, so a calorie-based result that is not whole is shown to the nearest gram.

Related tools

More: Health & Fitness