Health & Fitness
One-Rep Max (1RM) Calculator
Estimate your one-rep max from the weight and reps you lifted with the Epley, Brzycki and Lombardi formulas, plus a percentage chart for programming.
For general information only — not medical advice. Results are estimates; talk to a doctor or qualified health professional about your own health.
How to use
- 1Enter the weight you lifted and how many clean reps you did (ideally 2–10).
- 2Use the percentage table to plan training weights.
How it's calculated
Epley: 1RM = w × (1 + reps ÷ 30). Brzycki: w × 36 ÷ (37 − reps). Lombardi: w × reps^0.10. The average is shown as the estimate.
Frequently asked questions
How accurate are 1RM estimates?
Best with 2–10 reps. Beyond about 12 reps the formulas become unreliable because endurance plays a bigger role.
Should I test my true 1RM?
Only with good technique, a warm-up and a spotter or safety bars. Many lifters prefer estimates to avoid the risk.
What percentage should I train at?
Roughly 85%+ of 1RM for strength (1–5 reps), 67–85% for muscle growth (6–12 reps) and below 67% for endurance.
Why three formulas instead of one
Epley, Brzycki and Lombardi were each derived by fitting a curve to real lifters' performance across a handful of reps and extrapolating to what weight they could theoretically lift for just one. They use different shapes to do it — Epley is linear in reps, Brzycki is a ratio that approaches infinity as reps near 37, and Lombardi uses a power curve — which is exactly why they can disagree slightly even on the same input. This calculator averages all three rather than picking one, on the logic that no single formula is reliably 'more correct' across every rep range and bar weight, so splitting the difference reduces the error from any one formula's blind spot.
Why the estimate falls apart past about 10–12 reps
All three formulas assume that how much weight drops off as reps increase reflects pure strength endurance, but past roughly 10–12 reps, a set to failure starts being limited by factors these formulas don't model well — local muscular endurance, pacing, and even motivation to grind out a long set. That's why the guidance here caps reliable estimation at 2–10 reps: a 1RM projected from a 20-rep set is extrapolating the curve far outside the range it was fit to, and the three formulas tend to diverge from each other more sharply exactly in that zone.
What the percentage table is actually for
The training-percentage table isn't a fourth formula — it takes the averaged 1RM estimate and applies standard strength-training percentage bands (100% down to 60%) with the rep ranges those percentages typically support, which is a separate body of programming convention rather than something derived from Epley, Brzycki or Lombardi directly. It's meant as a quick reference for writing a training week: pick the percentage that matches the rep range and intensity you're training that day, and the table converts it straight to a loadable weight rounded to the nearest half unit.
Worked example: One-Rep Max (1RM) Calculator
Lifting 100 kg for 5 reps gives an Epley estimate of 100 × (1 + 5/30) ≈ 116.7 kg, a Brzycki estimate of 100 × 36/32 = 112.5 kg, and a Lombardi estimate of 100 × 5^0.1 ≈ 117.5 kg — a spread of about 5 kg between the lowest and highest. Averaging the three puts the estimated 1RM around 115.5 kg, and the percentage table would then suggest roughly 98 kg (85%) for a 6-rep strength set or 86.5 kg (75%) for a 10-rep hypertrophy set, both rounded to the nearest half kilogram.
Related tools
- Heart Rate Zone Calculator
Calculate your five heart rate training zones and target heart rate with the Karvonen (heart rate reserve) method or a simple % of max.
- Body Fat Calculator (US Navy Method)
Estimate body fat percentage from your neck, waist (and hip) measurements and height with the US Navy tape method, plus fat and lean mass.
- Ideal Weight Calculator
Estimate ideal body weight from height and sex with the Devine, Robinson, Miller and Hamwi formulas — alongside the healthy BMI weight range.
- Lean Body Mass & FFMI Calculator
Estimate lean body mass with the Boer formula (or from your body fat %) and your fat-free mass index (FFMI), normalized to 1.8 m.
- Race Time Predictor
Predict your 5K, 10K, half marathon and marathon times from a recent race result using Riegel's formula.
- Earthquake Magnitude & Energy Calculator
Compare earthquakes by magnitude: the energy released, the TNT equivalent and how many times stronger one quake is than another.