Account

What new tool do you want?

Auto & Travel

Horsepower, Torque, Displacement & 0–60 Calculator

Convert torque and RPM to horsepower, calculate engine displacement from bore and stroke, and estimate 0–60 mph and quarter-mile times from power and weight.

How to use

  1. 1Enter torque and RPM for horsepower; bore, stroke and cylinders for displacement.
  2. 2Enter power and vehicle weight for performance estimates.

How it's calculated

HP = torque (lb·ft) × RPM ÷ 5,252. Displacement = π ÷ 4 × bore² × stroke × cylinders. Quarter mile (Hale): ET ≈ 5.825 × (weight ÷ hp)^⅓ s; trap ≈ 234 × (hp ÷ weight)^⅓ mph.

Frequently asked questions

Why do horsepower and torque cross at 5,252 rpm?

Because HP = torque × RPM ÷ 5,252, the two are numerically equal at exactly 5,252 rpm (in lb·ft and hp).

How accurate are the 0–60 estimates?

Rough — traction, gearing, launch control and drivetrain losses matter a lot. Use them to compare, not predict.

Crank or wheel horsepower?

Manufacturers quote crank (engine) power; wheel power is typically 10–20% lower after drivetrain losses.

Why torque and horsepower always cross at exactly 5,252 rpm

Horsepower is defined as torque × RPM ÷ 5,252 when torque is measured in lb·ft — a conversion constant that falls out of the mechanical definition of a horsepower (550 ft·lb per second) combined with converting RPM to radians per second. Because of that fixed constant, whenever torque and horsepower are plotted on the same dyno chart in their conventional units, the two curves mathematically must cross at precisely 5,252 rpm, every time, for every engine — it's not a coincidence of any particular engine's design, just an artifact of the units chosen.

Worked example: Horsepower, Torque, Displacement & 0–60 Calculator

300 lb·ft of torque at exactly 5,252 rpm gives 300 × 5,252 ÷ 5,252 = 300 hp — the crossover point in action. A 4-cylinder engine with an 86mm bore and 86mm stroke (a 'square' engine, where bore equals stroke) computes to 1,998cc of displacement — essentially the 2.0-liter turbo-four displacement used by a huge number of mainstream production cars, which is a useful sanity check that the bore/stroke formula (π/4 × bore² × stroke × cylinders) is working as expected.

Why the 0–60 and quarter-mile numbers are rough by design

The Hale-style quarter-mile formula (ET ≈ 5.825 × (weight ÷ hp)^⅓) was built from drag-strip data of many different vehicles and only looks at power-to-weight ratio — it has no idea whether your tires can actually put that power down without wheelspin, how the gearing is set up, or how much the drivetrain loses power to friction before it reaches the wheels. These estimates are useful for comparing two power-to-weight ratios against each other, not for predicting an actual time slip.

Displacement is still computed when I only cared about the quarter mile

Every box is always active. Torque and rpm, default 300 pound-feet at 5,000 rpm, become horsepower and kilowatts using a factor of about 0.7457, even if I opened the page for the quarter-mile estimate. Bore, stroke, and cylinders, default 86 millimetres and 4 cylinders, always produce a displacement, with a hint in litres and cubic inches. The performance lines use vehicle power and weight, default 300 horsepower and 3,500 pounds, and that ratio has to be greater than zero. Quarter-mile time follows 5.825 times the cube root of weight over horsepower. Trap speed uses 234 times the cube root of the inverse ratio. The 0 to 60 estimate is a straight line, 0.108 times the ratio plus 1.1 seconds, rougher than the quarter-mile fit.

Related tools

More: Auto & Travel