Science & Engineering
Torque & Gear Ratio Calculator
Calculate torque from force and lever arm, and a gear train's ratio, output speed and output torque from the tooth counts.
How to use
- 1For torque, enter the force, lever length and angle.
- 2For gears, enter the driving and driven tooth counts, input speed and input torque.
How it's calculated
Torque τ = F × r × sin θ. Gear ratio = driven teeth ÷ driving teeth. Output speed = input speed ÷ ratio; output torque = input torque × ratio (ignoring losses).
Frequently asked questions
How do gears trade speed for torque?
A larger driven gear turns more slowly but with more torque; power (speed × torque) stays the same apart from friction losses.
Why does the angle matter for torque?
Only the part of the force perpendicular to the lever turns it. Pushing straight along the wrench gives no torque.
How do I convert N·m to lb·ft?
1 N·m ≈ 0.7376 lb·ft. Use the torque converter for other units.
Why only the sine of the angle counts
Torque only comes from the component of force that's perpendicular to the lever arm — push or pull straight along the length of a wrench and it won't turn the bolt at all, no matter how hard you push, because that force has no rotational effect. The sin θ term captures exactly this: it's 1 (maximum torque) at a 90° angle, where the force is fully perpendicular, and drops to 0 at 0° or 180°, where the force points straight along the lever and contributes nothing to rotation.
A worked example of the speed-for-torque trade
A 100 N force applied perpendicular (90°) to a 0.3 m lever gives 100 × 0.3 × sin90° = 30 N·m of torque — about 22.1 lb·ft. Separately, a gear train with a 12-tooth driver turning a 36-tooth driven gear has a 36 ÷ 12 = 3:1 ratio: an input spinning at 1,800 rpm with 10 N·m of torque comes out the other side at 1,800 ÷ 3 = 600 rpm but 10 × 3 = 30 N·m — three times slower, three times more torque.
Why power stays (almost) the same either way
Power is torque × angular speed, and the gear ratio trades one for the other in exactly inverse proportion — multiply torque by 3 and divide speed by 3, and the product is unchanged. Real gear trains lose a small amount of that power to friction between meshing teeth and in the bearings, typically a few percent per stage, which is why this calculator's output torque and speed figures are a close approximation rather than an exact real-world prediction.
Both answers always print, and the ratio is trimmed to three decimals
The wrench and the gears are one form. A 100 newton force at 90 degrees on a 0.3 metre lever is 30 newton-metres, also shown in pound-feet using a factor of about 0.7376. At the same time a 12-tooth driver and a 36-tooth driven gear, 1,800 rpm, and 10 newton-metres in, produce a 3 : 1 ratio, 600 rpm out, and 30 newton-metres out. The ratio text is rounded to three decimal places before the : 1 is added, so a ratio that is not a clean integer does not show a long tail. The driving tooth count has to be greater than zero. An angle of 0 degrees makes the torque line 0, because none of the force is perpendicular to the lever.
Related tools
- Hemocytometer Cell Count Calculator
Calculate cell concentration and viability from hemocytometer counts: cells per mL, total cells, and the volume needed to seed a target number of cells.
- Molar Mass Calculator
Calculate the molar mass (molecular weight) of any chemical formula — including brackets and hydrates like CuSO4·5H2O — with the mass percentage of each element.
- Molarity & Dilution Calculator
Calculate molarity, moles, mass or volume of a solution, or solve a dilution with C₁V₁ = C₂V₂.
- Density, Mass & Volume Calculator
Solve density = mass ÷ volume for any of the three, with a list of common material densities for reference.
- Customer Lifetime Value (CLV) Calculator
Estimate customer lifetime value from average order value, purchase frequency, gross margin and retention — and compare it with acquisition cost.
- Cycling Gear, Cadence & Speed Calculator
Calculate bike speed from cadence and gearing (chainring, cog, wheel size), plus gear ratio, gear inches and development.