Account

What new tool do you want?

Video & Audio

Volume Booster (Make Audio Louder)

Make quiet audio louder — boost volume by up to +30 dB with a built-in limiter that prevents harsh clipping — then save as MP3 or WAV.

How to use

  1. 1Add a quiet audio file.
  2. 2Raise the boost until it sounds right (preview it), then download.

Frequently asked questions

Will boosting distort my audio?

A soft limiter bends peaks smoothly instead of clipping. Very large boosts still flatten dynamics — use Normalize for consistent levels.

Can I boost a video's volume?

Add the video to extract and boost its audio; to keep the picture, use the video tools.

What's a dB?

+6 dB roughly doubles the signal level; +10 dB sounds about twice as loud.

A worked example of the before/after peak readout

If your quiet recording peaks at -24dBFS and you apply a +18dB boost, a simple multiplication would land the new peak at -6dBFS — safely below 0dBFS (digital full scale, the loudest a digital signal can represent before hard clipping). The tool reports exactly this as a note: 'Peak -24.0 → -6.0 dBFS,' letting you see at a glance whether your chosen boost pushed the audio close to the ceiling. If the math would have pushed the peak above roughly -0.3dBFS instead, the built-in limiter engages to prevent it.

Why the limiter targets -0.3dBFS specifically, not 0dBFS exactly

The gain function is called with a ceiling parameter of -0.3dB rather than 0dB, which leaves a small intentional safety margin below true digital maximum. This matters because downstream processing — converting to MP3, playing through a device's own output stage, or a streaming platform's loudness normalization — can introduce tiny overshoots of its own right at the sample level; audio engineers conventionally leave headroom in the -0.3 to -1dB range specifically so a file that technically 'just touches' full scale here doesn't come out clipped after a later, unavoidable processing step.

Why a soft limiter sounds different from just turning the boost down

Rather than cutting off any sample that would exceed the ceiling (hard clipping, which produces harsh, audibly distorted square-off edges on waveform peaks), a soft limiter detects when a sample is approaching the ceiling and smoothly bends its curve downward as it gets closer — gently compressing just the loudest peaks rather than slicing them flat. That's why a large boost here still sounds listenable rather than crackly even when it's working hard to tame the signal, though pushed far enough it inevitably flattens the audio's natural dynamic range (the difference between its quiet and loud moments) — which is exactly when the FAQ's suggestion to use Normalize instead becomes the better tool for the job, since normalizing adjusts overall level without this kind of peak-dependent compression.

Only the loudest peaks bend, starting around −1.2 dB

Every boost multiplies the level — ten to the power of the decibels divided by 20 — and then applies a soft ceiling at −0.3 dB. That ceiling is about 96.6% of full scale. The bend starts at 90% of the ceiling, around −1.2 dB. Samples that stay under that line, including a modest boost, are only multiplied. Louder ones curve toward the ceiling and are not allowed past it, so the file never quite touches full scale. The slider opens at +6 dB, a multiply of about 2, and runs from −20 dB, which is one tenth of the level, up to +30 dB, about 32 times.

A completely silent file shows a peak of −240 dB

The peak line is the loudest moment in the file, in decibels. True silence would make that figure undefined, so the quietest level it will report is a trillionth of full scale, which comes out as −240 dB. You see that both on the current-peak line and in the before-and-after note. Turning the slider down moves the audio away from the −1.2 dB bend, so a cut does not engage the soft ceiling unless the file was already peaking in that top band. The downloaded name includes the slider value with its sign, so the default file ends in +6dB.

Related tools

More: Video & Audio