Science & Engineering
Beam Deflection & Bending Moment Calculator
Calculate maximum deflection, bending moment, stress and reactions for simply supported and cantilever beams with point or uniform loads — rectangular sections in wood, steel or aluminum.
How to use
- 1Pick the support type and load type, then enter the span and load.
- 2Enter the beam's cross-section (width × depth) and material. Compare deflection with a limit like span/360.
How it's calculated
Simply supported: point load at center δ = PL³/48EI, M = PL/4; uniform load δ = 5wL⁴/384EI, M = wL²/8. Cantilever: end point load δ = PL³/3EI, M = PL; uniform δ = wL⁴/8EI, M = wL²/2. For a rectangle I = bd³/12 and bending stress σ = M·(d/2)/I.
Frequently asked questions
What deflection limit should I use?
Common limits are span/360 for floors (to avoid cracking finishes), span/240 for roofs, and span/180 for cantilevers. Check your local building code.
Is this enough to design a beam?
No — it's for estimates and learning. Real designs also check shear, bearing, buckling, load combinations and code safety factors. Consult an engineer for structural work.
Why does depth matter so much?
Stiffness grows with the cube of depth: doubling a beam's depth makes it 8 times stiffer, while doubling its width only doubles it.
Why deflection, not strength, usually decides the size
A 45×220 mm pine joist spanning 3 m under a 2 kN point load bends only about 2.8 mm — span/1,066, far inside the span/360 limit (about 8.3 mm) this calculator checks against. That gap is normal: timber and steel beams in everyday structures are almost always sized by stiffness, not by how close they are to breaking. Span/360 isn't a strength limit at all — it's a serviceability line, chosen because floors that sag more than that start cracking plaster, popping tile grout, and feeling bouncy underfoot, long before the beam is anywhere near its actual bending capacity.
Why a cantilever bends so much more than a simple span
For the same span, load and section, a cantilever's end-point-load deflection (PL³/3EI) is 16 times larger than a simply supported beam's center-point-load deflection (PL³/48EI) — all because one end is completely unsupported instead of having a prop at each side. The bending moment tells the same story: a cantilever's fixed end carries M = PL, four times the PL/4 moment at the center of a simple span. That's the mechanical reason a balcony or deck ledger needs a noticeably deeper beam than a floor joist carrying the same load over the same span.
What the second moment of area is actually measuring
I = bd³/12 for a rectangle isn't an arbitrary formula — it measures how far the material sits from the beam's neutral axis, squared and integrated over the cross-section, because material farther from the neutral axis resists bending more effectively per unit of area. That's why depth dominates: doubling the width only doubles I, but doubling the depth multiplies it by 8, which is also why steel I-beams push most of their material into top and bottom flanges rather than a solid rectangle. This tool reports I in cm⁴ so you can cross-check it against a span table or hand calculation.
What this estimate leaves out
The beam's own weight, shear stress near supports, lateral-torsional buckling of slender sections, bearing stress at the supports, and code-mandated load factors are all absent here. Real design also combines multiple load cases (dead, live, snow, wind) rather than a single point or uniform load. Treat the numbers as a sanity check on proportions, not a substitute for a span table or an engineer's sign-off on anything load-bearing.
Related tools
- Hemocytometer Cell Count Calculator
Calculate cell concentration and viability from hemocytometer counts: cells per mL, total cells, and the volume needed to seed a target number of cells.
- Molar Mass Calculator
Calculate the molar mass (molecular weight) of any chemical formula — including brackets and hydrates like CuSO4·5H2O — with the mass percentage of each element.
- Molarity & Dilution Calculator
Calculate molarity, moles, mass or volume of a solution, or solve a dilution with C₁V₁ = C₂V₂.
- pH Calculator
Calculate pH, pOH, [H⁺] and [OH⁻] from any one of them — or the pH of a weak acid from its concentration and Ka.
- Half-Life Calculator
Calculate how much of a radioactive isotope or drug remains after a given time — or the half-life or time from the amounts — with exponential decay.
- Density, Mass & Volume Calculator
Solve density = mass ÷ volume for any of the three, with a list of common material densities for reference.