Home & DIY
Screw & Bolt Thread Size Chart (Metric & UNC)
Metric (M2–M24) and UNC (#4–3/4") thread chart with pitch, threads per inch, tap drill and clearance hole sizes — plus a tap drill calculator for any thread.
How to use
- 1Look up the thread size in the chart.
- 2For non-standard threads, enter the major diameter and pitch (or TPI) to get the tap drill size.
How it's calculated
Tap drill ≈ major diameter − pitch (about 75% thread engagement). For inch threads: tap drill ≈ major diameter − 1 ÷ TPI.
Frequently asked questions
What does M8 × 1.25 mean?
An 8 mm major diameter with 1.25 mm between threads. Coarse pitch is the default if no pitch is given (M8 = M8 × 1.25).
What's a clearance hole?
A hole the bolt passes through freely without engaging threads — slightly larger than the bolt's diameter.
What's the difference between UNC and UNF?
UNC is coarse (fewer threads per inch, faster to assemble); UNF is fine (more threads, stronger in thin material and more resistant to vibration).
Why the tap drill formula is an approximation
Tap drill = major diameter − pitch isn't exact thread geometry — it's a widely used rule of thumb that targets about 75% thread engagement, the sweet spot where a tapped hole is strong enough for most jobs but doesn't need excessive torque to cut (which breaks taps in harder metals or blind holes). Full 100% engagement is stronger but dramatically increases tapping effort and breakage risk for little real strength gain, since the threads themselves are rarely the weakest link in a joint. If you're tapping something load-critical or brittle like cast iron, look up the exact drill size in a machinist's reference rather than relying on the 75% approximation alone.
Tap drill vs. clearance hole — don't mix them up
These solve opposite problems. A tap drill removes just enough material so the tap can cut new threads into the hole — that's what joins a bolt to a block of metal with no nut. A clearance hole is deliberately larger than the bolt's major diameter so the bolt passes through freely and the threads do their gripping somewhere else (typically a nut or a tapped hole on the far side). Drilling a clearance-sized hole where you meant to tap it leaves nothing for the threads to bite into.
Why only UNC appears in the reference table
The built-in chart covers Unified National Coarse because it's the default choice for general-purpose fastening in inch-based hardware. UNF (fine thread) uses more threads per inch at the same diameter, which gives finer adjustment and better vibration resistance in thin material, at the cost of being slower to assemble and more prone to cross-threading. The calculator above the table isn't limited to the chart, though — enter any major diameter and pitch or TPI, metric or inch, and it will compute the tap drill for threads the table doesn't list, including fine threads.
A worked example, and where it diverges from the standard
For an M8 × 1.25 bolt, the formula gives 8 − 1.25 = 6.75 mm. The reference table above, which lists the official ISO recommended tap drill for M8, shows 6.8 mm instead — a 0.05 mm difference. Neither is wrong: the formula targets a clean 75% engagement in general-purpose materials, while the ISO figure reflects tested real-world tapping performance across a range of metals. For a one-off bracket in mild steel, either drill works; if you're matching a published spec sheet exactly, use the table value over the calculated one.
Related tools
- Mattress & Bed Size Chart (US, UK, EU)
Compare mattress sizes across the US, UK and Europe — twin, full, queen, king, super king — in inches and centimetres, with suggested rug sizes for each bed.
- Will It Fit? Furniture Through a Door
Check whether a sofa, fridge or other furniture will fit through a doorway or hallway — including tilting it on its side or at an angle.
- Roofing Calculator (Squares & Shingles)
Calculate roof area from the house footprint and roof pitch, then the roofing squares, shingle bundles, underlayment rolls and cost.
- Cleaning Schedule Maker
Make a printable house cleaning schedule — daily, weekly, monthly and seasonal chores, spread across the week and shared between household members.
- eSign a PDF with Multiple Signers (Free, No Upload)
Send a PDF for signature to several people: place signature boxes for each signer, then everyone signs in turn in their browser. When the last person signs, a signing certificate with an audit trail and SHA-256 fingerprints is added. No account, nothing uploaded.
- Paper Sizes Chart (A4, Letter, A3…)
Every common paper size — A0–A7, B, envelopes, US Letter, Legal, Tabloid and photo sizes — in millimeters, inches and pixels at 300 DPI.